--- title: "Dishwasher Error Codes — What They Mean" description: "What a dishwasher error code can and cannot tell you, which ones only report a setting, and how to read one properly before you book." url: "https://dishwasherrepair.center/error-codes/" --- Error codes # Dishwasher error codes, read properly. A code narrows the search and is also the thing most often read wrong: the same characters mean different things on different brands, and a fair number of the codes people look up are not failures at all — they are modes the appliance was left in. ## Find your code, make by make. Type the characters exactly as the display shows them, or pick the make. Each code has a page of its own: what it means on that brand, what to check, and what not to do. ### ASKO dishwasher error codes 10 codes - [F10 Drain F10 means the water in the tub rose above the first overfill limit.](https://dishwasherrepair.center/error-codes/asko-f10/) - [F11 Drain F11 says the water could not be drained out of the tub.](https://dishwasherrepair.center/error-codes/asko-f11/) - [F12 Water supply F12 means water is not coming in properly.](https://dishwasherrepair.center/error-codes/asko-f12/) - [F40 Water supply F40 means the inlet valve is letting water through when it should be closed.](https://dishwasherrepair.center/error-codes/asko-f40/) - [F41 Heating F41 is the heater code on Asko's newer panels.](https://dishwasherrepair.center/error-codes/asko-f41/) - [F45 Wash motor and circulation F45 means the diverter, the part that routes water between spray arms or zones, is not working as it should.](https://dishwasherrepair.center/error-codes/asko-f45/) - [F52 Drain F52 is Asko's signal that the coarse and fine filters need cleaning.](https://dishwasherrepair.center/error-codes/asko-f52/) - [F54 Water supply F54 means the overflow guard has tripped because the water rose above the normal level.](https://dishwasherrepair.center/error-codes/asko-f54/) - [F56 Wash motor and circulation F56 means the circulation pump, which pushes water through the spray arms, has a problem.](https://dishwasherrepair.center/error-codes/asko-f56/) - [F68 Drain F68 is a problem reported by the brushless (BLDC) drain pump on Asko's newer machines.](https://dishwasherrepair.center/error-codes/asko-f68/) [ASKO dishwasher repair](https://dishwasherrepair.center/brands/asko/) ### Bosch dishwasher error codes 10 codes - [E15 Leak detected E15 means the dishwasher's leak protection has tripped: a safety switch found water sitting in the base, below the tub.](https://dishwasherrepair.center/error-codes/bosch-e15/) - [E24 Drain E24 says water is not leaving the dishwasher the way it should.](https://dishwasherrepair.center/error-codes/bosch-e24/) - [E25 Drain E25 is a drain code that Bosch ties to the pump end of the drain path: a pump that is blocked, a pump cover that is not seated, or a hose or air gap choked with debris.](https://dishwasherrepair.center/error-codes/bosch-e25/) - [E22 Drain E22 on a Bosch usually means the filter at the bottom of the tub is clogged with food.](https://dishwasherrepair.center/error-codes/bosch-e22/) - [E23 Drain E23 points at the drain pump itself: Bosch says the pump is blocked, clogged or defective.](https://dishwasherrepair.center/error-codes/bosch-e23/) - [E16 Water supply E16 means water is not getting into the dishwasher as it should.](https://dishwasherrepair.center/error-codes/bosch-e16/) - [E18 Water supply E18 means the water level in the tub is too low, or water is not being pumped around properly.](https://dishwasherrepair.center/error-codes/bosch-e18/) - [E14 Water supply E14 reports that the flow meter, which counts the water coming in, has failed, or that something is wrong with the fill system.](https://dishwasherrepair.center/error-codes/bosch-e14/) - [E09 Heating E09 says the heater inside Bosch's heat pump has reported an error, so the wash water may not be heated.](https://dishwasherrepair.center/error-codes/bosch-e09/) - [E27 Mode, not a failure E27 means the electricity reaching the dishwasher is too low.](https://dishwasherrepair.center/error-codes/bosch-e27/) [Bosch dishwasher repair](https://dishwasherrepair.center/brands/bosch/) ### Fisher & Paykel dishwasher error codes 10 codes - [A1 Water supply A DishDrawer drawer did not get the water it needed to wash.](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a1/) - [A3 Drain The drawer could not pump its water out.](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a3/) - [A6 Wash motor and circulation The spray arm in the drawer has come loose or off its mounting, or the water pressure is too low to drive it.](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a6/) - [A09 Heating A Sanitize wash did not reach the temperature needed to sanitize the dishes.](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a09/) - [A11 Heating The element in the drawer overheated because soil has built up on it.](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a11/) - [A10 Water supply A Fisher & Paykel built-in dishwasher got no water, or not enough: the tap may be off, the pressure too low, or the inlet hose bent.](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a10/) - [A20 Drain The waste water is not leaving the built-in dishwasher.](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a20/) - [F30 Leak detected The flood switch in the base of a Fisher & Paykel built-in dishwasher has been triggered.](https://dishwasherrepair.center/error-codes/fisher-and-paykel-f30/) - [A60 Heating The built-in dishwasher reported a water temperature error.](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a60/) - [A70 Sensor circuit An alarm from the temperature sensing on a Fisher & Paykel built-in dishwasher.](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a70/) [Fisher & Paykel dishwasher repair](https://dishwasherrepair.center/brands/fisher-and-paykel/) ### GE dishwasher error codes 10 codes - [LEAK DETECTED Leak detected The leak sensor in the base found water, so the dishwasher pumped out and canceled the cycle.](https://dishwasherrepair.center/error-codes/ge-leak-detected/) - [999 Leak detected On GE machines with the Floor Protect with Alert feature, 999 means a possible leak was found and the dishwasher will not start.](https://dishwasherrepair.center/error-codes/ge-999-floor-protect/) - [C1 Drain The pump-out at the end of a wash ran longer than two minutes, which tells the control that water is leaving the tub too slowly.](https://dishwasherrepair.center/error-codes/ge-c1/) - [C3 Drain The control could not get the water out of the tub at all.](https://dishwasherrepair.center/error-codes/ge-c3/) - [FTD Drain FTD stands for failure to drain: the cycle ended its pump-out and the tub still held water.](https://dishwasherrepair.center/error-codes/ge-ftd/) - [H2O Water supply Too little water came in during the fill.](https://dishwasherrepair.center/error-codes/ge-h2o/) - [C4 Water supply GE lists three possible reasons: the machine filled twice after a power interruption, the float switch is stuck or failed, or the drain or sump is clogged.](https://dishwasherrepair.center/error-codes/ge-c4/) - [C6 Heating The water arriving from the house is not hot enough for the cycle.](https://dishwasherrepair.center/error-codes/ge-c6/) - [C7 Sensor circuit The circuit that reads water temperature has stopped working, so the control cannot tell how hot the wash is.](https://dishwasherrepair.center/error-codes/ge-c7/) - [PrS Sensor circuit The pressure sensor that tracks the water level is sending the control a reading it cannot use, so a cycle either will not start or cancels itself.](https://dishwasherrepair.center/error-codes/ge-prs/) [GE dishwasher repair](https://dishwasherrepair.center/brands/ge/) ### Kenmore dishwasher error codes 10 codes - [F8E1 Drain On Kenmore HE models F8E1 is a slow drain: the water is leaving, but not quickly enough for the control.](https://dishwasherrepair.center/error-codes/kenmore-f8e1-he/) - [F8E2 Drain Sears describes F8E2 on the Kenmore HE family as a drain pump electrical problem, which is to say the pump circuit rather than a clog.](https://dishwasherrepair.center/error-codes/kenmore-f8e2-he/) - [F6E1 Water supply A Kenmore HE showing F6E1 did not fill.](https://dishwasherrepair.center/error-codes/kenmore-f6e1-he/) - [F6E4 Water supply Sears lists F6E4 on the Kenmore HE as the float switch reading open.](https://dishwasherrepair.center/error-codes/kenmore-f6e4-he/) - [F7E1 Heating On the Kenmore HE, F7E1 says the heating element does not work.](https://dishwasherrepair.center/error-codes/kenmore-f7e1-he/) - [F2E2 Communication Kenmore HE F2E2: the user interface control on the door cannot communicate with the electronic control board.](https://dishwasherrepair.center/error-codes/kenmore-f2e2-he/) - [IE Water supply IE on a Kenmore 722 series dishwasher means it is not filling.](https://dishwasherrepair.center/error-codes/kenmore-ie-722/) - [OE Drain OE on the Kenmore 722 series is a drain code: the dishwasher is not draining.](https://dishwasherrepair.center/error-codes/kenmore-oe-722/) - [AE Leak detected A Kenmore 722 series showing AE, or E1, has detected a water leak.](https://dishwasherrepair.center/error-codes/kenmore-ae-722/) - [Clean light blinks 7 times Heating On a Kenmore 665 model, seven blinks of the Clean light report a heater circuit failure: the water did not warm up as expected while the element was on.](https://dishwasherrepair.center/error-codes/kenmore-clean-light-7-blinks-665/) [Kenmore dishwasher repair](https://dishwasherrepair.center/brands/kenmore/) ### LG dishwasher error codes 10 codes - [AE Leak detected Water has leaked inside the machine and lifted the float switch in the base pan.](https://dishwasherrepair.center/error-codes/lg-ae/) - [IE Water supply The tub had not filled to its level after ten minutes, so the dishwasher stopped waiting for water.](https://dishwasherrepair.center/error-codes/lg-ie/) - [OE Drain LG's drain error: the water did not leave the tub.](https://dishwasherrepair.center/error-codes/lg-oe/) - [HE Heating The heater could not warm the water, or the water went above 149°F.](https://dishwasherrepair.center/error-codes/lg-he/) - [tE Sensor circuit The thermistor that reads water temperature reported a problem, or the water went above 194°F.](https://dishwasherrepair.center/error-codes/lg-te/) - [LE Wash motor and circulation The wash motor is not running as the control expects.](https://dishwasherrepair.center/error-codes/lg-le/) - [FE Water supply The machine found too much water in the tub and started the drain pump on its own to bring the level down.](https://dishwasherrepair.center/error-codes/lg-fe/) - [nE Wash motor and circulation LG's vario motor, which switches the water between the spray arms, is not responding as it should.](https://dishwasherrepair.center/error-codes/lg-ne/) - [CL Mode, not a failure Control lock is switched on — a setting, not an error.](https://dishwasherrepair.center/error-codes/lg-cl/) - [PF Mode, not a failure The power to the dishwasher was interrupted.](https://dishwasherrepair.center/error-codes/lg-pf/) [LG dishwasher repair](https://dishwasherrepair.center/brands/lg/) ### Miele dishwasher error codes 10 codes - [F1 Sensor circuit F1 means the sensor that measures the water and heating temperature has short-circuited.](https://dishwasherrepair.center/error-codes/miele-f1/) - [F11 Drain F11 means the dishwasher could not pump its water out and water is left in the tub.](https://dishwasherrepair.center/error-codes/miele-f11-g1000-g6000/) - [F11 Drain On the newer Miele series, F11 with water left in the tub points to a drain pump cover that is sitting wrong, or to a blocked drain pump that lets water flow back into the cabinet.](https://dishwasherrepair.center/error-codes/miele-f11-g7000/) - [F12 Water supply F12 is a water inlet code: water is blocked or restricted on its way into the dishwasher.](https://dishwasherrepair.center/error-codes/miele-f12/) - [F14 Wash motor and circulation F14 means the circulation pump is stuck.](https://dishwasherrepair.center/error-codes/miele-f14/) - [F78 Wash motor and circulation F78 is another Miele code for a blocked circulation pump.](https://dishwasherrepair.center/error-codes/miele-f78/) - [F18 Water supply F18 means the water intake valve has failed.](https://dishwasherrepair.center/error-codes/miele-f18/) - [F24 Heating F24 points at the heating relay, the electrical contact that switches the heater on and off.](https://dishwasherrepair.center/error-codes/miele-f24/) - [F25 Heating F25 is Miele's code for a problem reaching the desired temperature: the wash water was not brought to the temperature the program set.](https://dishwasherrepair.center/error-codes/miele-f25/) - [F70 Leak detected F70 means the Waterproof system has reacted.](https://dishwasherrepair.center/error-codes/miele-f70/) [Miele dishwasher repair](https://dishwasherrepair.center/brands/miele/) ### Samsung dishwasher error codes 10 codes - [LC Leak detected Samsung's leak sensor has found moisture in the base.](https://dishwasherrepair.center/error-codes/samsung-lc/) - [5C Drain Samsung's drain error: the dishwasher cannot empty the tub.](https://dishwasherrepair.center/error-codes/samsung-5c/) - [4C Water supply Water is not reaching the machine at the pressure or temperature it needs.](https://dishwasherrepair.center/error-codes/samsung-4c/) - [HE Heating Samsung names HE a heater error and explains it as the machine reading the temperature inside the tub incorrectly.](https://dishwasherrepair.center/error-codes/samsung-he/) - [tE Sensor circuit The temperature sensor is giving a reading the board does not trust.](https://dishwasherrepair.center/error-codes/samsung-te/) - [3C Wash motor and circulation Samsung says the pump has failed to run — the wash pump that moves water through the spray system.](https://dishwasherrepair.center/error-codes/samsung-3c/) - [OC Water supply There is more water in the tub than there should be.](https://dishwasherrepair.center/error-codes/samsung-oc/) - [CE Communication The control panel cannot talk to the rest of the dishwasher.](https://dishwasherrepair.center/error-codes/samsung-ce/) - [1E Drain Waterwall models: the filter is clogged.](https://dishwasherrepair.center/error-codes/samsung-1e-waterwall/) - [1E Heating Rotary models: the tub is running too hot.](https://dishwasherrepair.center/error-codes/samsung-1e-rotary/) [Samsung dishwasher repair](https://dishwasherrepair.center/brands/samsung/) ### Thermador dishwasher error codes 10 codes - [E15 Leak detected On a Thermador, E15 tells you the leakage protection has switched on because a safety switch sensed water in the base of the machine.](https://dishwasherrepair.center/error-codes/thermador-e15/) - [E22 Drain E22 on a Thermador most often comes from a clogged filter.](https://dishwasherrepair.center/error-codes/thermador-e22/) - [E23 Drain Thermador's E23 is about the drain pump: it is blocked, clogged or has failed.](https://dishwasherrepair.center/error-codes/thermador-e23/) - [E24 Drain E24 means the Thermador could not pump its water away.](https://dishwasherrepair.center/error-codes/thermador-e24/) - [E25 Drain E25 on a Thermador is a blocked-drain code.](https://dishwasherrepair.center/error-codes/thermador-e25/) - [E16 Water supply E16 tells you water is having trouble getting into the Thermador.](https://dishwasherrepair.center/error-codes/thermador-e16/) - [E18 Water supply E18 means the Thermador sees too little water in the tub, or the water is not being pumped correctly.](https://dishwasherrepair.center/error-codes/thermador-e18/) - [E12 Heating E12 means limescale has built up in the heat pump.](https://dishwasherrepair.center/error-codes/thermador-e12/) - [E27 Mode, not a failure E27 says the voltage feeding the Thermador is too low.](https://dishwasherrepair.center/error-codes/thermador-e27/) - [UP Mode, not a failure UP is not an error.](https://dishwasherrepair.center/error-codes/thermador-up/) [Thermador dishwasher repair](https://dishwasherrepair.center/brands/thermador/) ### Whirlpool dishwasher error codes 10 codes - [F9E1 Drain The drain phase ran longer than the control allows, so water was still in the tub when it should have been gone.](https://dishwasherrepair.center/error-codes/whirlpool-f9e1/) - [F9E2 Drain The control could not run the drain motor the way it expected.](https://dishwasherrepair.center/error-codes/whirlpool-f9e2/) - [H2O Water supply The dishwasher opened its fill valve and did not sense water arriving.](https://dishwasherrepair.center/error-codes/whirlpool-h2o/) - [F8E4 Leak detected Water has collected in the drip tray under the tub and lifted the float switch there, so the machine stops.](https://dishwasherrepair.center/error-codes/whirlpool-f8e4/) - [F8E5 Water supply The fill valve is not closing, so water keeps coming in when the control has asked it to stop.](https://dishwasherrepair.center/error-codes/whirlpool-f8e5/) - [F6E4 Water supply The float switch that watches for too much water has been triggered.](https://dishwasherrepair.center/error-codes/whirlpool-f6e4/) - [F4E2 Heating The control found a problem in the heating system, the element and the circuit that warms wash water and dries the load.](https://dishwasherrepair.center/error-codes/whirlpool-f4e2/) - [F7E2 Wash motor and circulation The wash motor, which drives water up through the spray arms, is not running as the control expects.](https://dishwasherrepair.center/error-codes/whirlpool-f7e2/) - [F3E2 Sensor circuit One of the sensors the control reads has given a bad signal: the thermistor that measures water temperature or the optical sensor that judges how dirty the water is.](https://dishwasherrepair.center/error-codes/whirlpool-f3e2/) - [F1E2 Communication The main control lost communication with the rest of the electronics.](https://dishwasherrepair.center/error-codes/whirlpool-f1e2/) [Whirlpool dishwasher repair](https://dishwasherrepair.center/brands/whirlpool/) ### Gaggenau dishwasher error codes 8 codes - [E:2060 Heating E:2060 means the dishwasher has found scale on its heating element.](https://dishwasherrepair.center/error-codes/gaggenau-e2060/) - [E:3000 Leak detected E:3000 means the dishwasher's water protection system has been activated.](https://dishwasherrepair.center/error-codes/gaggenau-e3000/) - [E:3200 Water supply E:3200, or a lit water supply indicator, means not enough water is coming in.](https://dishwasherrepair.center/error-codes/gaggenau-e3200/) - [E:3400 Water supply E:3400 means water keeps running into the dishwasher without stopping.](https://dishwasherrepair.center/error-codes/gaggenau-e3400/) - [E:6102 Drain E:6102 means the drain pump cover is loose or something is jamming the pump.](https://dishwasherrepair.center/error-codes/gaggenau-e6102/) - [E:6103 Drain E:6103 with water left in the tub means the water cannot drain.](https://dishwasherrepair.center/error-codes/gaggenau-e6103/) - [E:9001 Mode, not a failure E:9001 means the voltage reaching the dishwasher is too low.](https://dishwasherrepair.center/error-codes/gaggenau-e9001/) - [E:9240 Drain E:9240 means the filters are dirty or blocked.](https://dishwasherrepair.center/error-codes/gaggenau-e9240/) [Gaggenau dishwasher repair](https://dishwasherrepair.center/brands/gaggenau/) ### KitchenAid dishwasher error codes 8 codes - [F9E1 Drain KitchenAid's label for F9E1 is a long drain: emptying the tub took longer than the control permits.](https://dishwasherrepair.center/error-codes/kitchenaid-f9e1/) - [F9E2 Drain KitchenAid ties F9E2 to the drain motor: the control tried to pump water out and the motor did not respond properly.](https://dishwasherrepair.center/error-codes/kitchenaid-f9e2/) - [H2O Water supply H2O on a KitchenAid means the machine is not detecting water after it called for a fill.](https://dishwasherrepair.center/error-codes/kitchenaid-h2o/) - [F8E4 Leak detected The float in the drip tray beneath the tub has been raised by water, and the dishwasher has halted to stop more from escaping.](https://dishwasherrepair.center/error-codes/kitchenaid-f8e4/) - [F8E5 Water supply The water valve is stuck in the open position on this KitchenAid, letting water in beyond what the cycle asked for.](https://dishwasherrepair.center/error-codes/kitchenaid-f8e5/) - [F6E3 Wash motor and circulation The sensing system has found foam in the tub.](https://dishwasherrepair.center/error-codes/kitchenaid-f6e3/) - [F4E3 Heating KitchenAid lists F4E3 as a heating error: the control saw something wrong while heating water or drying.](https://dishwasherrepair.center/error-codes/kitchenaid-f4e3/) - [F2E2 Communication The control and the rest of the electronics stopped exchanging signals.](https://dishwasherrepair.center/error-codes/kitchenaid-f2e2/) [KitchenAid dishwasher repair](https://dishwasherrepair.center/brands/kitchenaid/) ### Maytag dishwasher error codes 8 codes - [F9E1 Drain Maytag uses F9E1 for a drain that took too long.](https://dishwasherrepair.center/error-codes/maytag-f9e1/) - [H2O Water supply On a Maytag, H2O says the dishwasher expected water to come in and could not detect any.](https://dishwasherrepair.center/error-codes/maytag-h2o/) - [F8E4 Leak detected Maytag's F8E4 means water is sitting in the drip tray under the tub.](https://dishwasherrepair.center/error-codes/maytag-f8e4/) - [F8E5 Water supply The fill valve on this Maytag has stuck open, so water keeps entering after it should stop.](https://dishwasherrepair.center/error-codes/maytag-f8e5/) - [F7E2 Wash motor and circulation F7E2 on a Maytag points to the wash motor: the part that circulates water through the arms did not run as the control asked.](https://dishwasherrepair.center/error-codes/maytag-f7e2/) - [F6E1 Communication The user interface, the panel you press, and the main control are not working together.](https://dishwasherrepair.center/error-codes/maytag-f6e1/) - [F8E2 Water supply Maytag assigns F8E2 to an electrical problem with the fill valve, the valve that lets water into the tub.](https://dishwasherrepair.center/error-codes/maytag-f8e2/) - [F4E2 Heating Maytag uses F4E2 to report trouble in the heating system that warms the water and dries the dishes.](https://dishwasherrepair.center/error-codes/maytag-f4e2/) [Maytag dishwasher repair](https://dishwasherrepair.center/brands/maytag/) ### Viking dishwasher error codes 7 codes - [Both lights flashing Leak detected When both indicator lights flash together without stopping, the Viking dishwasher is reporting a pan flood — water in the base pan.](https://dishwasherrepair.center/error-codes/viking-both-lights-flashing/) - [1-5 Drain A Viking drain error: the Pots/Pans light flashes once and the Normal Wash light five times.](https://dishwasherrepair.center/error-codes/viking-1-5/) - [2-2 Water supply A Viking fill timeout: the dishwasher did not fill in the time allowed.](https://dishwasherrepair.center/error-codes/viking-2-2/) - [3-3 Drain Viking's drain pump error, shown as three flashes on each light.](https://dishwasherrepair.center/error-codes/viking-3-3/) - [3-1 Communication Viking's UI-MC communication error: the user interface on the door and the motor control are not talking.](https://dishwasherrepair.center/error-codes/viking-3-1/) - [4-1 Sensor circuit Viking's temperature sensor error, shown as four flashes on Pots/Pans and one on Normal Wash.](https://dishwasherrepair.center/error-codes/viking-4-1/) - [1-2 Wash motor and circulation Viking's motor control status error: the board that runs the wash motor reported a problem.](https://dishwasherrepair.center/error-codes/viking-1-2/) [Viking dishwasher repair](https://dishwasherrepair.center/brands/viking/) ### Bertazzoni dishwasher error codes 6 codes - [FF Water supply FF means the water inlet system has failed to bring water in.](https://dishwasherrepair.center/error-codes/bertazzoni-ff/) - [F1 Leak detected F1 is Bertazzoni's overflow alarm.](https://dishwasherrepair.center/error-codes/bertazzoni-f1/) - [F2 Drain F2 means the dishwasher cannot discharge its water.](https://dishwasherrepair.center/error-codes/bertazzoni-f2/) - [F3 Water supply F3 means water keeps coming into the dishwasher without stopping.](https://dishwasherrepair.center/error-codes/bertazzoni-f3/) - [F6 Sensor circuit F6 points at the heater sensor, which the manual lists as not working properly.](https://dishwasherrepair.center/error-codes/bertazzoni-f6/) - [F8 Heating F8 means the dishwasher has reported a problem with its heater.](https://dishwasherrepair.center/error-codes/bertazzoni-f8/) [Bertazzoni dishwasher repair](https://dishwasherrepair.center/brands/bertazzoni/) ### Dacor dishwasher error codes 6 codes - [LC Leak detected Dacor's leakage check: the dishwasher has detected a leak.](https://dishwasherrepair.center/error-codes/dacor-lc/) - [4C Water supply Dacor's water supply check: water is not coming in as it should.](https://dishwasherrepair.center/error-codes/dacor-4c/) - [5C Drain Dacor's drain check: the dishwasher is not draining.](https://dishwasherrepair.center/error-codes/dacor-5c/) - [HC Heating Dacor's high-temperature heating check: the machine flagged its heating as running too hot.](https://dishwasherrepair.center/error-codes/dacor-hc/) - [3C Wash motor and circulation Dacor's pump operation check: the wash pump did not run as expected.](https://dishwasherrepair.center/error-codes/dacor-3c/) - [1C Water supply Dacor's low-water level check: there is not enough water in the tub for the wash.](https://dishwasherrepair.center/error-codes/dacor-1c/) [Dacor dishwasher repair](https://dishwasherrepair.center/brands/dacor/) ### Electrolux dishwasher error codes 6 codes - [i20 Drain For an Electrolux, i20 reports a drain that did not complete: water stayed in the tub past the drain step.](https://dishwasherrepair.center/error-codes/electrolux-i20/) - [i40 Drain Electrolux uses i40 for a clogged filter or sump, where food residue has collected under the wash area.](https://dishwasherrepair.center/error-codes/electrolux-i40/) - [CL Mode, not a failure CL or Cd on an Electrolux means the door is not fully shut and latched.](https://dishwasherrepair.center/error-codes/electrolux-cl/) - [Hd Mode, not a failure Hd or HO on an Electrolux is a heat delay: the cycle pauses while water warms to the temperature it needs.](https://dishwasherrepair.center/error-codes/electrolux-hd/) - [PF Mode, not a failure PF on an Electrolux means the unit lost power partway through.](https://dishwasherrepair.center/error-codes/electrolux-pf/) - [01-24 Mode, not a failure On an Electrolux, 01 to 24 in the display is a delay-start timer in hours; the cycle waits until it counts down.](https://dishwasherrepair.center/error-codes/electrolux-01-24/) [Electrolux dishwasher repair](https://dishwasherrepair.center/brands/electrolux/) ### Frigidaire dishwasher error codes 6 codes - [i20 Drain Frigidaire's i20 says the dishwasher did not drain properly, so water was left in the tub at the end of a drain step.](https://dishwasherrepair.center/error-codes/frigidaire-i20/) - [i40 Drain On a Frigidaire, i40 reports a clogged filter or sump: food soil has built up where the water collects before it is pumped.](https://dishwasherrepair.center/error-codes/frigidaire-i40/) - [CL Mode, not a failure CL, sometimes Cd, means the Frigidaire's door has not closed and latched.](https://dishwasherrepair.center/error-codes/frigidaire-cl/) - [Hd Mode, not a failure Hd or HO is not a failure: the Frigidaire is holding the cycle while it heats the water.](https://dishwasherrepair.center/error-codes/frigidaire-hd/) - [PF Mode, not a failure PF tells you the Frigidaire lost power, most often a brief outage during a cycle.](https://dishwasherrepair.center/error-codes/frigidaire-pf/) - [01-24 Mode, not a failure A number from 01 to 24 is the Delay Start count in hours, not an error.](https://dishwasherrepair.center/error-codes/frigidaire-01-24/) [Frigidaire dishwasher repair](https://dishwasherrepair.center/brands/frigidaire/) ### JennAir dishwasher error codes 6 codes - [F9E1 Drain JennAir labels F9E1 a long drain.](https://dishwasherrepair.center/error-codes/jennair-f9e1/) - [F9E2 Drain JennAir reserves F9E2 for a drain motor error, meaning the control could not drive the pump that empties the tub.](https://dishwasherrepair.center/error-codes/jennair-f9e2/) - [F8E4 Leak detected On a JennAir, F8E4 means the drip tray below the tub holds water and its float has shut the cycle down.](https://dishwasherrepair.center/error-codes/jennair-f8e4/) - [F8E5 Water supply JennAir's F8E5 reports a fill valve stuck open: water is still flowing in when the control wants it closed.](https://dishwasherrepair.center/error-codes/jennair-f8e5/) - [F6E4 Water supply JennAir's F6E4 points to the water float switch, which guards against too much water in the tub.](https://dishwasherrepair.center/error-codes/jennair-f6e4/) - [F7E2 Wash motor and circulation JennAir lists F7E2 as a wash motor error: the motor that pushes water through the spray arms is not running normally.](https://dishwasherrepair.center/error-codes/jennair-f7e2/) [JennAir dishwasher repair](https://dishwasherrepair.center/brands/jennair/) ### SKS dishwasher error codes 6 codes - [AE Leak detected SKS reports a water leak.](https://dishwasherrepair.center/error-codes/sks-ae/) - [IE Water supply A water inlet problem on an SKS dishwasher: water is not coming in as it should.](https://dishwasherrepair.center/error-codes/sks-ie/) - [OE Drain An SKS drainage problem: the water is not getting out of the tub.](https://dishwasherrepair.center/error-codes/sks-oe/) - [HE Heating SKS reports a heater circuit failure.](https://dishwasherrepair.center/error-codes/sks-he/) - [tE Sensor circuit The SKS water temperature sensor (the thermistor) has failed.](https://dishwasherrepair.center/error-codes/sks-te/) - [LE Wash motor and circulation An SKS wash motor error.](https://dishwasherrepair.center/error-codes/sks-le/) [SKS dishwasher repair](https://dishwasherrepair.center/brands/sks/) ### Smeg dishwasher error codes 6 codes - [E1 Leak detected E1 means the anti-flooding Acquastop system has tripped because of a water leak.](https://dishwasherrepair.center/error-codes/smeg-e1/) - [E2 Water supply E2 means the system that limits the water level inside the dishwasher has tripped.](https://dishwasherrepair.center/error-codes/smeg-e2/) - [E3 Heating E3 means the water is not being heated, or the heating is not going as the program expects.](https://dishwasherrepair.center/error-codes/smeg-e3/) - [E4 Sensor circuit E4 means something is wrong with the way the dishwasher monitors water temperature.](https://dishwasherrepair.center/error-codes/smeg-e4/) - [E5 Water supply E5 means the dishwasher is not taking in water, or not taking it in correctly.](https://dishwasherrepair.center/error-codes/smeg-e5/) - [E6 Drain E6 means water is not being pumped out, or not pumped out correctly.](https://dishwasherrepair.center/error-codes/smeg-e6/) [Smeg dishwasher repair](https://dishwasherrepair.center/brands/smeg/) ### Fulgor Milano dishwasher error codes 5 codes - [E1 Leak detected On a Fulgor Milano dishwasher, E1 says the Acquastop anti-flooding system has tripped because water leaked.](https://dishwasherrepair.center/error-codes/fulgor-milano-e1/) - [E2 Water supply E2 is the safety level alarm: the device that caps how high the water can rise in the tub has tripped.](https://dishwasherrepair.center/error-codes/fulgor-milano-e2/) - [E3 Heating E3 means the wash water is not heated, or is heated incorrectly.](https://dishwasherrepair.center/error-codes/fulgor-milano-e3/) - [E5 Water supply E5 means the dishwasher is not drawing in water, or draws it in incorrectly.](https://dishwasherrepair.center/error-codes/fulgor-milano-e5/) - [E6 Drain E6 means the dishwasher cannot pump the water out, or pumps it out incorrectly.](https://dishwasherrepair.center/error-codes/fulgor-milano-e6/) [Fulgor Milano dishwasher repair](https://dishwasherrepair.center/brands/fulgor-milano/) ### ZLINE dishwasher error codes 4 codes - [E1 Water supply E1 means the ZLINE dishwasher took too long to fill.](https://dishwasherrepair.center/error-codes/zline-e1/) - [E4 Leak detected E4 is ZLINE's overflow warning: water has reached the bottom of the unit and tripped the flood switch.](https://dishwasherrepair.center/error-codes/zline-e4/) - [E9 Mode, not a failure E9 on a ZLINE Classic means a button has been held down for more than 30 seconds.](https://dishwasherrepair.center/error-codes/zline-e9/) - [Ed Communication Ed means the ZLINE's display board and main board have lost communication for longer than the control tolerates.](https://dishwasherrepair.center/error-codes/zline-ed/) [ZLINE dishwasher repair](https://dishwasherrepair.center/brands/zline/) ### Cove dishwasher error codes 3 codes - [800115 Drain Cove prints it as “Error 800115.](https://dishwasherrepair.center/error-codes/cove-800115/) - [560186 Water supply Cove shows “Error 560186.](https://dishwasherrepair.center/error-codes/cove-560186/) - [980199 Mode, not a failure The power was interrupted during a cycle.](https://dishwasherrepair.center/error-codes/cove-980199/) [Cove dishwasher repair](https://dishwasherrepair.center/brands/cove/) ### Café dishwasher error codes 1 code - [LEAK DETECTED Leak detected The Café leak protection found water in the base, drained the tub and canceled the cycle.](https://dishwasherrepair.center/error-codes/cafe-leak-detected/) [Café dishwasher repair](https://dishwasherrepair.center/brands/cafe/) ### GE Profile dishwasher error codes 1 code - [LEAK DETECTED Leak detected A GE Profile dishwasher with leak protection sensed water where it should not be, emptied the tub and stopped the wash.](https://dishwasherrepair.center/error-codes/ge-profile-leak-detected/) [GE Profile dishwasher repair](https://dishwasherrepair.center/brands/ge-profile/) ### Monogram dishwasher error codes 1 code - [LEAK DETECTED Leak detected Monogram's leak protection sensed water under the tub.](https://dishwasherrepair.center/error-codes/monogram-leak-detected/) [Monogram dishwasher repair](https://dishwasherrepair.center/brands/monogram/) ### Only confirmed codes Every code here is taken from the manufacturer's own documentation, never from a forum or a parts listing. If yours is not listed, book with the exact characters and the full model number, and we will tell you whether it is one we take. ## Three things before you look it up. A code is a lead, not a verdict. These decide whether the answer you find will be any use. 01 ### Exactly what the display shows Each character, in order, and whether it blinks. Take a photo before you press anything — opening the door or canceling the cycle can wipe some codes off the panel. 02 ### The complete model number It is printed on a label along the edge of the door or the side of the tub. One code can mean a drain issue on one make and a heater issue on another. 03 ### Is water on the floor? That one answer decides whether you shut the supply valve and switch off the breaker now, or simply book the next open window. ## What each kind of code means. Codes fall into a handful of families. The family says more about the likely repair than the characters do — and one of them is not a repair at all. [How to read a code](https://dishwasherrepair.center/problems/dishwasher-error-code/) ### Mode, not a failure 16 codes A setting someone turned on, or a reminder the machine shows on purpose — a control lock, a demo mode, a rinse-aid prompt. Nothing is broken and no part is needed. [E27](https://dishwasherrepair.center/error-codes/bosch-e27/) [980199](https://dishwasherrepair.center/error-codes/cove-980199/) [CL](https://dishwasherrepair.center/error-codes/electrolux-cl/) [Hd](https://dishwasherrepair.center/error-codes/electrolux-hd/) [PF](https://dishwasherrepair.center/error-codes/electrolux-pf/) [01-24](https://dishwasherrepair.center/error-codes/electrolux-01-24/) [CL](https://dishwasherrepair.center/error-codes/frigidaire-cl/) [Hd](https://dishwasherrepair.center/error-codes/frigidaire-hd/) [PF](https://dishwasherrepair.center/error-codes/frigidaire-pf/) [01-24](https://dishwasherrepair.center/error-codes/frigidaire-01-24/) [E:9001](https://dishwasherrepair.center/error-codes/gaggenau-e9001/) [CL](https://dishwasherrepair.center/error-codes/lg-cl/) [PF](https://dishwasherrepair.center/error-codes/lg-pf/) [E27](https://dishwasherrepair.center/error-codes/thermador-e27/) [UP](https://dishwasherrepair.center/error-codes/thermador-up/) [E9](https://dishwasherrepair.center/error-codes/zline-e9/) Usually leads to No repair — the setting is changed back Shows up as [Dishwasher Not Starting](https://dishwasherrepair.center/problems/dishwasher-not-starting/) [Dishwasher Showing an Error Code](https://dishwasherrepair.center/problems/dishwasher-error-code/) ### Drain 47 codes Water did not leave the tub in the time the control expects. A clogged filter, a kinked hose or a blocked disposal inlet are ruled out before the drain pump. [F10](https://dishwasherrepair.center/error-codes/asko-f10/) [F11](https://dishwasherrepair.center/error-codes/asko-f11/) [F52](https://dishwasherrepair.center/error-codes/asko-f52/) [F68](https://dishwasherrepair.center/error-codes/asko-f68/) [F2](https://dishwasherrepair.center/error-codes/bertazzoni-f2/) [E24](https://dishwasherrepair.center/error-codes/bosch-e24/) [E25](https://dishwasherrepair.center/error-codes/bosch-e25/) [E22](https://dishwasherrepair.center/error-codes/bosch-e22/) [E23](https://dishwasherrepair.center/error-codes/bosch-e23/) [800115](https://dishwasherrepair.center/error-codes/cove-800115/) [5C](https://dishwasherrepair.center/error-codes/dacor-5c/) [i20](https://dishwasherrepair.center/error-codes/electrolux-i20/) [i40](https://dishwasherrepair.center/error-codes/electrolux-i40/) [A3](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a3/) [A20](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a20/) [i20](https://dishwasherrepair.center/error-codes/frigidaire-i20/) [i40](https://dishwasherrepair.center/error-codes/frigidaire-i40/) [E6](https://dishwasherrepair.center/error-codes/fulgor-milano-e6/) [E:6102](https://dishwasherrepair.center/error-codes/gaggenau-e6102/) [E:6103](https://dishwasherrepair.center/error-codes/gaggenau-e6103/) [E:9240](https://dishwasherrepair.center/error-codes/gaggenau-e9240/) [C1](https://dishwasherrepair.center/error-codes/ge-c1/) [C3](https://dishwasherrepair.center/error-codes/ge-c3/) [FTD](https://dishwasherrepair.center/error-codes/ge-ftd/) [F9E1](https://dishwasherrepair.center/error-codes/jennair-f9e1/) [F9E2](https://dishwasherrepair.center/error-codes/jennair-f9e2/) [F8E1](https://dishwasherrepair.center/error-codes/kenmore-f8e1-he/) [F8E2](https://dishwasherrepair.center/error-codes/kenmore-f8e2-he/) [OE](https://dishwasherrepair.center/error-codes/kenmore-oe-722/) [F9E1](https://dishwasherrepair.center/error-codes/kitchenaid-f9e1/) [F9E2](https://dishwasherrepair.center/error-codes/kitchenaid-f9e2/) [OE](https://dishwasherrepair.center/error-codes/lg-oe/) [F9E1](https://dishwasherrepair.center/error-codes/maytag-f9e1/) [F11](https://dishwasherrepair.center/error-codes/miele-f11-g1000-g6000/) [F11](https://dishwasherrepair.center/error-codes/miele-f11-g7000/) [5C](https://dishwasherrepair.center/error-codes/samsung-5c/) [1E](https://dishwasherrepair.center/error-codes/samsung-1e-waterwall/) [OE](https://dishwasherrepair.center/error-codes/sks-oe/) [E6](https://dishwasherrepair.center/error-codes/smeg-e6/) [E22](https://dishwasherrepair.center/error-codes/thermador-e22/) [E23](https://dishwasherrepair.center/error-codes/thermador-e23/) [E24](https://dishwasherrepair.center/error-codes/thermador-e24/) [E25](https://dishwasherrepair.center/error-codes/thermador-e25/) [1-5](https://dishwasherrepair.center/error-codes/viking-1-5/) [3-3](https://dishwasherrepair.center/error-codes/viking-3-3/) [F9E1](https://dishwasherrepair.center/error-codes/whirlpool-f9e1/) [F9E2](https://dishwasherrepair.center/error-codes/whirlpool-f9e2/) Usually leads to [Drain and pump repair](https://dishwasherrepair.center/services/drain-and-pump-repair/) Shows up as [Dishwasher Not Draining](https://dishwasherrepair.center/problems/dishwasher-not-draining/) [Dishwasher Smells Bad](https://dishwasherrepair.center/problems/dishwasher-smells/) ### Water supply 45 codes Not enough water arrived, or it arrived too slowly. The supply valve under the sink and the inlet screen are checked before the fill valve itself. [F12](https://dishwasherrepair.center/error-codes/asko-f12/) [F40](https://dishwasherrepair.center/error-codes/asko-f40/) [F54](https://dishwasherrepair.center/error-codes/asko-f54/) [FF](https://dishwasherrepair.center/error-codes/bertazzoni-ff/) [F3](https://dishwasherrepair.center/error-codes/bertazzoni-f3/) [E16](https://dishwasherrepair.center/error-codes/bosch-e16/) [E18](https://dishwasherrepair.center/error-codes/bosch-e18/) [E14](https://dishwasherrepair.center/error-codes/bosch-e14/) [560186](https://dishwasherrepair.center/error-codes/cove-560186/) [4C](https://dishwasherrepair.center/error-codes/dacor-4c/) [1C](https://dishwasherrepair.center/error-codes/dacor-1c/) [A1](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a1/) [A10](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a10/) [E2](https://dishwasherrepair.center/error-codes/fulgor-milano-e2/) [E5](https://dishwasherrepair.center/error-codes/fulgor-milano-e5/) [E:3200](https://dishwasherrepair.center/error-codes/gaggenau-e3200/) [E:3400](https://dishwasherrepair.center/error-codes/gaggenau-e3400/) [H2O](https://dishwasherrepair.center/error-codes/ge-h2o/) [C4](https://dishwasherrepair.center/error-codes/ge-c4/) [F8E5](https://dishwasherrepair.center/error-codes/jennair-f8e5/) [F6E4](https://dishwasherrepair.center/error-codes/jennair-f6e4/) [F6E1](https://dishwasherrepair.center/error-codes/kenmore-f6e1-he/) [F6E4](https://dishwasherrepair.center/error-codes/kenmore-f6e4-he/) [IE](https://dishwasherrepair.center/error-codes/kenmore-ie-722/) [H2O](https://dishwasherrepair.center/error-codes/kitchenaid-h2o/) [F8E5](https://dishwasherrepair.center/error-codes/kitchenaid-f8e5/) [IE](https://dishwasherrepair.center/error-codes/lg-ie/) [FE](https://dishwasherrepair.center/error-codes/lg-fe/) [H2O](https://dishwasherrepair.center/error-codes/maytag-h2o/) [F8E5](https://dishwasherrepair.center/error-codes/maytag-f8e5/) [F8E2](https://dishwasherrepair.center/error-codes/maytag-f8e2/) [F12](https://dishwasherrepair.center/error-codes/miele-f12/) [F18](https://dishwasherrepair.center/error-codes/miele-f18/) [4C](https://dishwasherrepair.center/error-codes/samsung-4c/) [OC](https://dishwasherrepair.center/error-codes/samsung-oc/) [IE](https://dishwasherrepair.center/error-codes/sks-ie/) [E2](https://dishwasherrepair.center/error-codes/smeg-e2/) [E5](https://dishwasherrepair.center/error-codes/smeg-e5/) [E16](https://dishwasherrepair.center/error-codes/thermador-e16/) [E18](https://dishwasherrepair.center/error-codes/thermador-e18/) [2-2](https://dishwasherrepair.center/error-codes/viking-2-2/) [H2O](https://dishwasherrepair.center/error-codes/whirlpool-h2o/) [F8E5](https://dishwasherrepair.center/error-codes/whirlpool-f8e5/) [F6E4](https://dishwasherrepair.center/error-codes/whirlpool-f6e4/) [E1](https://dishwasherrepair.center/error-codes/zline-e1/) Usually leads to [Fill and water valve repair](https://dishwasherrepair.center/services/fill-and-water-valve-repair/) Shows up as [Dishwasher Not Filling With Water](https://dishwasherrepair.center/problems/dishwasher-not-filling/) [Dishwasher Cycle Takes Too Long](https://dishwasherrepair.center/problems/dishwasher-cycle-too-long/) ### Heating 23 codes The water did not reach the temperature the cycle calls for in time. A heating element, its thermal cutoff or the sensor reading it. [F41](https://dishwasherrepair.center/error-codes/asko-f41/) [F8](https://dishwasherrepair.center/error-codes/bertazzoni-f8/) [E09](https://dishwasherrepair.center/error-codes/bosch-e09/) [HC](https://dishwasherrepair.center/error-codes/dacor-hc/) [A09](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a09/) [A11](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a11/) [A60](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a60/) [E3](https://dishwasherrepair.center/error-codes/fulgor-milano-e3/) [E:2060](https://dishwasherrepair.center/error-codes/gaggenau-e2060/) [C6](https://dishwasherrepair.center/error-codes/ge-c6/) [F7E1](https://dishwasherrepair.center/error-codes/kenmore-f7e1-he/) [Clean light blinks 7 times](https://dishwasherrepair.center/error-codes/kenmore-clean-light-7-blinks-665/) [F4E3](https://dishwasherrepair.center/error-codes/kitchenaid-f4e3/) [HE](https://dishwasherrepair.center/error-codes/lg-he/) [F4E2](https://dishwasherrepair.center/error-codes/maytag-f4e2/) [F24](https://dishwasherrepair.center/error-codes/miele-f24/) [F25](https://dishwasherrepair.center/error-codes/miele-f25/) [HE](https://dishwasherrepair.center/error-codes/samsung-he/) [1E](https://dishwasherrepair.center/error-codes/samsung-1e-rotary/) [HE](https://dishwasherrepair.center/error-codes/sks-he/) [E3](https://dishwasherrepair.center/error-codes/smeg-e3/) [E12](https://dishwasherrepair.center/error-codes/thermador-e12/) [F4E2](https://dishwasherrepair.center/error-codes/whirlpool-f4e2/) Usually leads to [Heating and drying repair](https://dishwasherrepair.center/services/heating-and-drying-repair/) Shows up as [Dishwasher Not Heating Water](https://dishwasherrepair.center/problems/dishwasher-not-heating/) [Dishwasher Not Drying Dishes](https://dishwasherrepair.center/problems/dishwasher-not-drying/) ### Leak detected 24 codes Water has reached the base pan under the tub and tripped the float that stops the cycle. Shut off the supply, find where it escaped, then dry the base. [F1](https://dishwasherrepair.center/error-codes/bertazzoni-f1/) [E15](https://dishwasherrepair.center/error-codes/bosch-e15/) [LEAK DETECTED](https://dishwasherrepair.center/error-codes/cafe-leak-detected/) [LC](https://dishwasherrepair.center/error-codes/dacor-lc/) [F30](https://dishwasherrepair.center/error-codes/fisher-and-paykel-f30/) [E1](https://dishwasherrepair.center/error-codes/fulgor-milano-e1/) [E:3000](https://dishwasherrepair.center/error-codes/gaggenau-e3000/) [LEAK DETECTED](https://dishwasherrepair.center/error-codes/ge-profile-leak-detected/) [LEAK DETECTED](https://dishwasherrepair.center/error-codes/ge-leak-detected/) [999](https://dishwasherrepair.center/error-codes/ge-999-floor-protect/) [F8E4](https://dishwasherrepair.center/error-codes/jennair-f8e4/) [AE](https://dishwasherrepair.center/error-codes/kenmore-ae-722/) [F8E4](https://dishwasherrepair.center/error-codes/kitchenaid-f8e4/) [AE](https://dishwasherrepair.center/error-codes/lg-ae/) [F8E4](https://dishwasherrepair.center/error-codes/maytag-f8e4/) [F70](https://dishwasherrepair.center/error-codes/miele-f70/) [LEAK DETECTED](https://dishwasherrepair.center/error-codes/monogram-leak-detected/) [LC](https://dishwasherrepair.center/error-codes/samsung-lc/) [AE](https://dishwasherrepair.center/error-codes/sks-ae/) [E1](https://dishwasherrepair.center/error-codes/smeg-e1/) [E15](https://dishwasherrepair.center/error-codes/thermador-e15/) [Both lights flashing](https://dishwasherrepair.center/error-codes/viking-both-lights-flashing/) [F8E4](https://dishwasherrepair.center/error-codes/whirlpool-f8e4/) [E4](https://dishwasherrepair.center/error-codes/zline-e4/) Usually leads to [Leak and seal repair](https://dishwasherrepair.center/services/leak-and-seal-repair/) Shows up as [Dishwasher Leaking Water](https://dishwasherrepair.center/problems/dishwasher-leaking-water/) ### Wash motor and circulation 15 codes The pump that pushes water through the spray arms is not running at the speed the control expects. Debris in the chopper or the pump is checked before the motor. [F45](https://dishwasherrepair.center/error-codes/asko-f45/) [F56](https://dishwasherrepair.center/error-codes/asko-f56/) [3C](https://dishwasherrepair.center/error-codes/dacor-3c/) [A6](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a6/) [F7E2](https://dishwasherrepair.center/error-codes/jennair-f7e2/) [F6E3](https://dishwasherrepair.center/error-codes/kitchenaid-f6e3/) [LE](https://dishwasherrepair.center/error-codes/lg-le/) [nE](https://dishwasherrepair.center/error-codes/lg-ne/) [F7E2](https://dishwasherrepair.center/error-codes/maytag-f7e2/) [F14](https://dishwasherrepair.center/error-codes/miele-f14/) [F78](https://dishwasherrepair.center/error-codes/miele-f78/) [3C](https://dishwasherrepair.center/error-codes/samsung-3c/) [LE](https://dishwasherrepair.center/error-codes/sks-le/) [1-2](https://dishwasherrepair.center/error-codes/viking-1-2/) [F7E2](https://dishwasherrepair.center/error-codes/whirlpool-f7e2/) Usually leads to [Wash motor and circulation](https://dishwasherrepair.center/services/wash-motor-and-circulation-repair/) Shows up as [Dishwasher Not Cleaning Dishes](https://dishwasherrepair.center/problems/dishwasher-not-cleaning/) [Dishwasher Making Loud Noise](https://dishwasherrepair.center/problems/dishwasher-loud-noise/) ### Sensor circuit 11 codes A temperature, turbidity or water-level sensor reporting a value outside its range, or the wiring to it. The reading is measured with a meter before any part is ordered. [F6](https://dishwasherrepair.center/error-codes/bertazzoni-f6/) [A70](https://dishwasherrepair.center/error-codes/fisher-and-paykel-a70/) [C7](https://dishwasherrepair.center/error-codes/ge-c7/) [PrS](https://dishwasherrepair.center/error-codes/ge-prs/) [tE](https://dishwasherrepair.center/error-codes/lg-te/) [F1](https://dishwasherrepair.center/error-codes/miele-f1/) [tE](https://dishwasherrepair.center/error-codes/samsung-te/) [tE](https://dishwasherrepair.center/error-codes/sks-te/) [E4](https://dishwasherrepair.center/error-codes/smeg-e4/) [4-1](https://dishwasherrepair.center/error-codes/viking-4-1/) [F3E2](https://dishwasherrepair.center/error-codes/whirlpool-f3e2/) Usually leads to [Controls and sensors](https://dishwasherrepair.center/services/controls-and-sensors/) Shows up as [Dishwasher Not Heating Water](https://dishwasherrepair.center/problems/dishwasher-not-heating/) [Dishwasher Cycle Takes Too Long](https://dishwasherrepair.center/problems/dishwasher-cycle-too-long/) ### Communication 7 codes The control board and the user panel on the door stopped talking to each other. The ribbon cable through the door hinge is checked before either board. [F2E2](https://dishwasherrepair.center/error-codes/kenmore-f2e2-he/) [F2E2](https://dishwasherrepair.center/error-codes/kitchenaid-f2e2/) [F6E1](https://dishwasherrepair.center/error-codes/maytag-f6e1/) [CE](https://dishwasherrepair.center/error-codes/samsung-ce/) [3-1](https://dishwasherrepair.center/error-codes/viking-3-1/) [F1E2](https://dishwasherrepair.center/error-codes/whirlpool-f1e2/) [Ed](https://dishwasherrepair.center/error-codes/zline-ed/) Usually leads to [Controls and sensors](https://dishwasherrepair.center/services/controls-and-sensors/) Shows up as [Dishwasher Control Panel Not Responding](https://dishwasherrepair.center/problems/control-panel-not-responding/) For the heart of your home. ## Questions about the codes. ### Why is my code missing from these pages? Only because nobody has written a checked page for it yet. A code is added here only when the manufacturer’s own documentation explains it. Record the characters and whether they blink, and include them in the booking so the technician can check them against your model. ### Does a code mean the same on every brand? No, and treating it that way leads people astray. A code that reports a drain problem on one make may report a heater or a water supply issue on another, and some makers change meanings between model years. Always read a code against the make and model. ### Can I clear a dishwasher code myself? Turning the power off at the breaker for a minute or two sometimes clears it, and if it never returns it was often a one-time event. A code that keeps coming back points to a real condition, and clearing it repeatedly only hides how often it happens. ### The panel shows a code but the dishes come out clean. Is something wrong? Not always. Some of the codes people search for are settings, such as a control lock, a demo mode or a reminder to add rinse aid, rather than anything broken. The code pages mark which are settings and how to turn each one off. --- **[Read on the site: Dishwasher Error Codes — What They Mean](https://dishwasherrepair.center/error-codes/)** **[Book a visit with DishwasherRepair.center](https://dishwasherrepair.center/schedule/)**