Frigidaire dishwasher
showing 01-24
A number from 01 to 24 is the Delay Start count in hours, not an error.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: Frigidaire
Book a visit
Three short steps, about a minute.
or call (844) 430-4286
Loading appointment form…
The appointment form couldn’t load. Please try again.
What 01-24
actually means.
A number from 01 to 24 is the Delay Start count in hours, not an error. The Frigidaire will begin once it reaches zero.
Frigidaire dishwasher display
What to do when 01-24 shows on the dishwasherKind of codeMode, not a failure
A setting someone turned on, or a reminder the machine shows on purpose — a control lock, a demo mode, a rinse-aid prompt. Nothing is broken and no part is needed.
Usually leads toNo repair
Press Cancel once to skip the delay and start the chosen cycle now.
Shows up asDishwasher Not Starting
The door is shut and a cycle is chosen, but nothing happens, or the lights come on and it will not run.
MakeFrigidaire
Widely installed, value-focused built-in dishwashers from the Electrolux group.
SourceFrigidaire owner support: Dishwasher Error Code 01-24
Frigidaire's owner-support articles for its dishwashers with a display; models without a display signal some of these events with flashing lights instead.
Before you book,
in this order.
Each step comes from Frigidaire's own guidance for 01-24 on its dishwashers. Follow it to the end: the last card says whether this is a visit.
Press Cancel once to skip the delay and start the chosen cycle now.
A second press cancels the cycle and drains; a third stops the drain and turns the unit off.
Nothing needs a visit unless the count refuses to cancel.
Cleared?
No part needed replacing. If the next full cycle still stops partway or leaves water in the tub, treat that as a new problem.
What not to do
01-24 is not a code to research further; someone pressed Delay Start.
What you may
notice with it.
The dishwasher problem 01-24 tends to arrive with. Answer these at the dishwasher before anyone is booked.
All problems
No repair indicated
Nothing to repair.
A setting someone turned on, or a reminder the machine shows on purpose — a control lock, a demo mode, a rinse-aid prompt. Nothing is broken and no part is needed.
Read these
before the visit.
Short guides that make the call quicker and the diagnosis cheaper.
All guidesFrigidaire
dishwashers.
Widely installed, value-focused built-in dishwashers from the Electrolux group.
Frigidaire dishwasher repair
In Frigidaire's own words
Error Code 01-24 indicates that the delay option has been enabled and will begin the cycle once the displayed time reaches 0.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Frigidaire's owner-support articles for its dishwashers with a display; models without a display signal some of these events with flashing lights instead.
Frigidaire 01-24 dishwasher repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about 01-24.
Can I clear 01-24 myself?
How do I stop the Delay Start count on my Frigidaire?
Does a Frigidaire showing 01-24 need service?
Back to your everyday
Still showing 01-24?
Book with the characters exactly as shown, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.