Maytag dishwasher
showing F8E4
Maytag's F8E4 means water is sitting in the drip tray under the tub.
Mon–Sat, 8am–8pm
- Leak detected
- Leak and seal repair
- Source: Maytag
Book a visit
Three short steps, about a minute.
or call (844) 430-4286
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F8E4
actually means.
Maytag's F8E4 means water is sitting in the drip tray under the tub. The float switch in that tray has stopped the dishwasher.
Maytag dishwasher display · also shown as Clean light: 8 blinks, pause, 4 blinks
What to do when F8E4 shows on the dishwasherKind of codeLeak detected
Water has reached the base pan under the tub and tripped the float that stops the cycle. Shut off the supply, find where it escaped, then dry the base.
Usually leads toLeak and seal repair
Water on the floor or under the unit, followed back to the gasket, the hoses, the pump seal or the tub.
Shows up asDishwasher Leaking Water
Water on the kitchen floor during or after a cycle, from the door, the corners or underneath.
MakeMaytag
Durable everyday dishwashers from Whirlpool Corporation, built with a focus on heavy use.
SourceMaytag product help: F8E4 error code
Documented on Maytag's product-help site for its dishwashers; a model without a display reports it as a blink count on the Clean light.
Before you book,
in this order.
Each step comes from Maytag's own guidance for F8E4 on its dishwashers. Follow it to the end: the last card says whether this is a visit.
Close the water supply to the dishwasher.
Press Cancel twice: the first press quiets the tone, the second clears the code.
Empty the drip tray, and on a new install make sure the float switch plug is fully seated.
Book a visit if water keeps finding its way into the tray.
What not to do
Unplugging the float switch to stop the alarm defeats the one part watching for a leak.
What you may
notice with it.
The dishwasher problem F8E4 tends to arrive with. Answer these at the dishwasher before anyone is booked.
All problems
Where F8E4 usually leads
Leak and seal repair.
Read these
before the visit.
Short guides that make the call quicker and the diagnosis cheaper.
All guidesMaytag
dishwashers.
Durable everyday dishwashers from Whirlpool Corporation, built with a focus on heavy use.
Maytag dishwasher repairMore Maytag codes
Leak detected on other makes
In Maytag's own words
Is the float switch connected?
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Documented on Maytag's product-help site for its dishwashers; a model without a display reports it as a blink count on the Clean light.
Maytag F8E4 dishwasher repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F8E4.
Can I clear F8E4 myself?
Can I disconnect the float switch to silence F8E4 on my Maytag?
Why would a new Maytag show F8E4 when I see no water?
Back to your everyday
Still showing F8E4?
Book with the characters exactly as shown, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.