Maytag dishwasher
showing F9E1
Maytag uses F9E1 for a drain that took too long.
Mon–Sat, 8am–8pm
- Drain
- Drain and pump repair
- Source: Maytag
Book a visit
Three short steps, about a minute.
or call (844) 430-4286
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F9E1
actually means.
Maytag uses F9E1 for a drain that took too long. The water left the tub slowly or not at all within the time the control allows.
Maytag dishwasher display · also shown as Clean light: 9 blinks, pause, 1 blink
What to do when F9E1 shows on the dishwasherKind of codeDrain
Water did not leave the tub in the time the control expects. A clogged filter, a kinked hose or a blocked disposal inlet are ruled out before the drain pump.
Usually leads toDrain and pump repair
Water left standing in the tub, cleared by finding where the drain path actually stops.
Shows up asDishwasher Not Draining
Dirty water stays in the bottom of the tub after the cycle ends.
MakeMaytag
Durable everyday dishwashers from Whirlpool Corporation, built with a focus on heavy use.
SourceMaytag product help: F9E1 error code
Documented on Maytag's product-help site for its dishwashers; a model without a display reports it as a blink count on the Clean light.
Before you book,
in this order.
Each step comes from Maytag's own guidance for F9E1 on its dishwashers. Follow it to the end: the last card says whether this is a visit.
Rinse the filter from the tub floor under running water until the mesh is clear.
Check the hose from the back of the dishwasher to the sink for a pinch or a clog.
Clear any food in the disposer, then give the control a 30-second power reset.
Book a visit if a clean filter and a clear hose do not end the code.
What not to do
A first cycle after installation that throws F9E1 usually points to the disposer knockout plug, not to a failed part.
What you may
notice with it.
The dishwasher problems F9E1 tends to arrive with. Answer these at the dishwasher before anyone is booked.
All problems
Dishwasher Not Draining
6 causes, cheapest first
Where F9E1 usually leads
Drain and pump repair.
Read these
before the visit.
Short guides that make the call quicker and the diagnosis cheaper.
All guidesMaytag
dishwashers.
Durable everyday dishwashers from Whirlpool Corporation, built with a focus on heavy use.
Maytag dishwasher repair
In Maytag's own words
Potential Cause: Long Drain
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Documented on Maytag's product-help site for its dishwashers; a model without a display reports it as a blink count on the Clean light.
Maytag F9E1 dishwasher repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F9E1.
Can I clear F9E1 myself?
Why did my Maytag throw F9E1 on its first load after installation?
What should I clean first for F9E1 on a Maytag?
Back to your everyday
Still showing F9E1?
Book with the characters exactly as shown, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.