KitchenAid dishwasher
showing F8E4
The float in the drip tray beneath the tub has been raised by water, and the dishwasher has halted to stop more from escaping.
Mon–Sat, 8am–8pm
- Leak detected
- Leak and seal repair
- Source: KitchenAid
Book a visit
Three short steps, about a minute.
or call (844) 430-4286
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F8E4
actually means.
The float in the drip tray beneath the tub has been raised by water, and the dishwasher has halted to stop more from escaping.
KitchenAid dishwasher display · also shown as Clean light: 8 blinks, pause, 4 blinks
What to do when F8E4 shows on the dishwasherKind of codeLeak detected
Water has reached the base pan under the tub and tripped the float that stops the cycle. Shut off the supply, find where it escaped, then dry the base.
Usually leads toLeak and seal repair
Water on the floor or under the unit, followed back to the gasket, the hoses, the pump seal or the tub.
Shows up asDishwasher Leaking Water
Water on the kitchen floor during or after a cycle, from the door, the corners or underneath.
MakeKitchenAid
Built-in dishwashers from Whirlpool Corporation known for their third racks and stainless interiors.
SourceKitchenAid product help: F8E4 error code
From KitchenAid's own product-help pages for its dishwashers; on panels without a readout the same code is flashed on the Clean light.
Before you book,
in this order.
Each step comes from KitchenAid's own guidance for F8E4 on its dishwashers. Follow it to the end: the last card says whether this is a visit.
Shut the supply valve before touching anything else.
Silence the tone with Cancel, then press Cancel again to clear F8E4.
Release the tray by pressing its side snaps inward, pull it toward you without straining the float wire, and pour it out.
If water reappears in the tray, book a visit to trace where it is escaping.
What not to do
Towels on the floor do not fix F8E4. The source of the water is inside the cabinet and has to be found.
What you may
notice with it.
The dishwasher problem F8E4 tends to arrive with. Answer these at the dishwasher before anyone is booked.
All problems
Where F8E4 usually leads
Leak and seal repair.
Read these
before the visit.
Short guides that make the call quicker and the diagnosis cheaper.
All guidesKitchenAid
dishwashers.
Built-in dishwashers from Whirlpool Corporation known for their third racks and stainless interiors.
KitchenAid dishwasher repairMore KitchenAid codes
Leak detected on other makes
In KitchenAid's own words
Does the drip tray need to be emptied?
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. From KitchenAid's own product-help pages for its dishwashers; on panels without a readout the same code is flashed on the Clean light.
KitchenAid F8E4 dishwasher repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F8E4.
Can I clear F8E4 myself?
Is it safe to keep using a KitchenAid after clearing F8E4?
How do I empty the drip tray for F8E4 on a KitchenAid without damage?
Back to your everyday
Still showing F8E4?
Book with the characters exactly as shown, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.