JennAir dishwasher
showing F7E2
JennAir lists F7E2 as a wash motor error: the motor that pushes water through the spray arms is not running normally.
Mon–Sat, 8am–8pm
- Wash motor and circulation
- Wash motor and circulation
- Source: JennAir
Book a visit
Three short steps, about a minute.
or call (844) 430-4286
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F7E2
actually means.
JennAir lists F7E2 as a wash motor error: the motor that pushes water through the spray arms is not running normally.
JennAir dishwasher display · also shown as Clean light: 7 blinks, pause, 2 blinks
What to do when F7E2 shows on the dishwasherKind of codeWash motor and circulation
The pump that pushes water through the spray arms is not running at the speed the control expects. Debris in the chopper or the pump is checked before the motor.
Usually leads toWash motor and circulation
The motor that throws the water at the dishes, and the most expensive part most dishwashers have.
Shows up asDishwasher Not Cleaning Dishes
Dishes come out with food stuck on, gritty film or spots that a full cycle should have removed.
MakeJennAir
Luxury built-in dishwashers from Whirlpool Corporation, offered in panel-ready and finished styles.
SourceJennAir product help: F7E2 error code
Taken from JennAir's product-help pages for its dishwashers; JennAir also describes reading such codes as Clean-light blink counts.
Before you book,
in this order.
Each step comes from JennAir's own guidance for F7E2 on its dishwashers. Follow it to the end: the last card says whether this is a visit.
Remove power for 30 seconds and restore it.
Run a short wash and check whether the arms spray.
Book a visit if F7E2 is displayed again.
Still there?
It usually turns into wash motor and circulation. Book with the code and the model number.
What not to do
Dirty dishes alongside F7E2 are a result of the motor issue, not a loading mistake.
What you may
notice with it.
The dishwasher problems F7E2 tends to arrive with. Answer these at the dishwasher before anyone is booked.
All problems
Dishwasher Not Cleaning Dishes
5 causes, cheapest first
Where F7E2 usually leads
Wash motor and circulation.
Read these
before the visit.
Short guides that make the call quicker and the diagnosis cheaper.
All guidesJennAir
dishwashers.
Luxury built-in dishwashers from Whirlpool Corporation, offered in panel-ready and finished styles.
JennAir dishwasher repair
In JennAir's own words
Troubleshooting: Power Cycle, If the error code returns, schedule service.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Taken from JennAir's product-help pages for its dishwashers; JennAir also describes reading such codes as Clean-light blink counts.
JennAir F7E2 dishwasher repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F7E2.
Can I clear F7E2 myself?
Why are my dishes dirty with JennAir F7E2?
Will a power reset fix JennAir F7E2?
Back to your everyday
Still showing F7E2?
Book with the characters exactly as shown, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.