JennAir dishwasher
showing F6E4
JennAir's F6E4 points to the water float switch, which guards against too much water in the tub.
Mon–Sat, 8am–8pm
- Water supply
- Fill and water valve repair
- Source: JennAir
Book a visit
Three short steps, about a minute.
or call (844) 430-4286
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F6E4
actually means.
JennAir's F6E4 points to the water float switch, which guards against too much water in the tub. A dishwasher sitting out of level can set it off.
JennAir dishwasher display · also shown as Clean light: 6 blinks, pause, 4 blinks
What to do when F6E4 shows on the dishwasherKind of codeWater supply
Not enough water arrived, or it arrived too slowly. The supply valve under the sink and the inlet screen are checked before the fill valve itself.
Usually leads toFill and water valve repair
A dishwasher that will not fill, fills too little, or keeps filling, traced through the valve, the float and the supply.
Shows up asDishwasher Not Filling With Water
The cycle starts and hums, but little or no water comes into the tub.
MakeJennAir
Luxury built-in dishwashers from Whirlpool Corporation, offered in panel-ready and finished styles.
SourceJennAir product help: F6E4 error code
Taken from JennAir's product-help pages for its dishwashers; JennAir also describes reading such codes as Clean-light blink counts.
Before you book,
in this order.
Each step comes from JennAir's own guidance for F6E4 on its dishwashers. Follow it to the end: the last card says whether this is a visit.
Place a level on the door opening and correct the leveling legs if needed.
Give the control a 30-second power reset.
Book a visit if a level machine still shows F6E4.
Still there?
It usually turns into fill and water valve repair. Book with the code and the model number.
What not to do
F6E4 is not always water on the floor. Tilt alone can move the float.
What you may
notice with it.
The dishwasher problems F6E4 tends to arrive with. Answer these at the dishwasher before anyone is booked.
All problems
Where F6E4 usually leads
Fill and water valve repair.
Read these
before the visit.
Short guides that make the call quicker and the diagnosis cheaper.
All guidesJennAir
dishwashers.
Luxury built-in dishwashers from Whirlpool Corporation, offered in panel-ready and finished styles.
JennAir dishwasher repair
In JennAir's own words
Incorrect leveling of the dishwasher can cause this error.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Taken from JennAir's product-help pages for its dishwashers; JennAir also describes reading such codes as Clean-light blink counts.
JennAir F6E4 dishwasher repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F6E4.
Can I clear F6E4 myself?
Can an uneven floor cause JennAir F6E4?
What does the float switch on a JennAir F6E4 do?
Back to your everyday
Still showing F6E4?
Book with the characters exactly as shown, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.