JennAir dishwasher
showing F9E1
JennAir labels F9E1 a long drain.
Mon–Sat, 8am–8pm
- Drain
- Drain and pump repair
- Source: JennAir
Book a visit
Three short steps, about a minute.
or call (844) 430-4286
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F9E1
actually means.
JennAir labels F9E1 a long drain. The pump-out took longer than the control accepts, leaving water behind.
JennAir dishwasher display · also shown as Clean light: 9 blinks, pause, 1 blink
What to do when F9E1 shows on the dishwasherKind of codeDrain
Water did not leave the tub in the time the control expects. A clogged filter, a kinked hose or a blocked disposal inlet are ruled out before the drain pump.
Usually leads toDrain and pump repair
Water left standing in the tub, cleared by finding where the drain path actually stops.
Shows up asDishwasher Not Draining
Dirty water stays in the bottom of the tub after the cycle ends.
MakeJennAir
Luxury built-in dishwashers from Whirlpool Corporation, offered in panel-ready and finished styles.
SourceJennAir product help: F9E1 error code
Taken from JennAir's product-help pages for its dishwashers; JennAir also describes reading such codes as Clean-light blink counts.
Before you book,
in this order.
Each step comes from JennAir's own guidance for F9E1 on its dishwashers. Follow it to the end: the last card says whether this is a visit.
Pull the filter and clean off the film and food caught in it.
Trace the drain hose to where it meets the sink or disposer and remove any blockage.
After a 30-second power reset, run a rinse to see if the tub empties.
Water that still stands after these steps is the point to book a visit.
What not to do
F9E1 does not call for a new pump straight away; JennAir's own list begins with the filter and the hose.
What you may
notice with it.
The dishwasher problem F9E1 tends to arrive with. Answer these at the dishwasher before anyone is booked.
All problems
Where F9E1 usually leads
Drain and pump repair.
Read these
before the visit.
Short guides that make the call quicker and the diagnosis cheaper.
All guidesJennAir
dishwashers.
Luxury built-in dishwashers from Whirlpool Corporation, offered in panel-ready and finished styles.
JennAir dishwasher repair
In JennAir's own words
Sink Disposer: If connected, ensure the disposer is clear and that the knockout plug was removed (for new installations).
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Taken from JennAir's product-help pages for its dishwashers; JennAir also describes reading such codes as Clean-light blink counts.
JennAir F9E1 dishwasher repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F9E1.
Can I clear F9E1 myself?
What does long drain mean on a JennAir F9E1?
Why does my JennAir show F9E1 as a Clean light blinking?
Back to your everyday
Still showing F9E1?
Book with the characters exactly as shown, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.