Whirlpool dishwasher
showing F8E4
Water has collected in the drip tray under the tub and lifted the float switch there, so the machine stops.
Mon–Sat, 8am–8pm
- Leak detected
- Leak and seal repair
- Source: Whirlpool
Book a visit
Three short steps, about a minute.
or call (844) 430-4286
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F8E4
actually means.
Water has collected in the drip tray under the tub and lifted the float switch there, so the machine stops. Whirlpool's overview page labels F8E4 water detected in the drip tray.
Whirlpool dishwasher display · also shown as Clean light: 8 blinks, pause, 4 blinks
What to do when F8E4 shows on the dishwasherKind of codeLeak detected
Water has reached the base pan under the tub and tripped the float that stops the cycle. Shut off the supply, find where it escaped, then dry the base.
Usually leads toLeak and seal repair
Water on the floor or under the unit, followed back to the gasket, the hoses, the pump seal or the tub.
Shows up asDishwasher Leaking Water
Water on the kitchen floor during or after a cycle, from the door, the corners or underneath.
MakeWhirlpool
Everyday built-in dishwashers from one of the largest appliance makers in the US.
SourceWhirlpool product help: F8E4 error code
Listed on Whirlpool's product-help site for its current built-in dishwashers; models without a display blink it on the Clean light.
Before you book,
in this order.
Each step comes from Whirlpool's own guidance for F8E4 on its dishwashers. Follow it to the end: the last card says whether this is a visit.
Close the water supply valve under the sink.
Press Cancel once to quiet the alarm and a second time to clear the code.
Slide the drip tray out gently, since the float wire stays attached, and empty it.
Book a visit if the tray fills again, so the leaking fitting or seal can be found.
What not to do
Clearing F8E4 without emptying the tray only brings it straight back, and the water underneath keeps soaking the floor.
What you may
notice with it.
The dishwasher problem F8E4 tends to arrive with. Answer these at the dishwasher before anyone is booked.
All problems
Where F8E4 usually leads
Leak and seal repair.
Read these
before the visit.
Short guides that make the call quicker and the diagnosis cheaper.
All guidesWhirlpool
dishwashers.
Everyday built-in dishwashers from one of the largest appliance makers in the US.
Whirlpool dishwasher repairMore Whirlpool codes
Leak detected on other makes
In Whirlpool's own words
If you see water in the drip tray, it must be emptied.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Listed on Whirlpool's product-help site for its current built-in dishwashers; models without a display blink it on the Clean light.
Whirlpool F8E4 dishwasher repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F8E4.
Can I clear F8E4 myself?
Why does F8E4 keep coming back on my Whirlpool?
How do I empty the drip tray for F8E4 on a Whirlpool?
Back to your everyday
Still showing F8E4?
Book with the characters exactly as shown, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.