Whirlpool dishwasher
showing F9E1
The drain phase ran longer than the control allows, so water was still in the tub when it should have been gone.
Mon–Sat, 8am–8pm
- Drain
- Drain and pump repair
- Source: Whirlpool
Book a visit
Three short steps, about a minute.
or call (844) 430-4286
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F9E1
actually means.
The drain phase ran longer than the control allows, so water was still in the tub when it should have been gone. Whirlpool calls it a long drain and points first at the filter, the hose and the sink connection.
Whirlpool dishwasher display · also shown as Clean light: 9 blinks, pause, 1 blink
What to do when F9E1 shows on the dishwasherKind of codeDrain
Water did not leave the tub in the time the control expects. A clogged filter, a kinked hose or a blocked disposal inlet are ruled out before the drain pump.
Usually leads toDrain and pump repair
Water left standing in the tub, cleared by finding where the drain path actually stops.
Shows up asDishwasher Not Draining
Dirty water stays in the bottom of the tub after the cycle ends.
MakeWhirlpool
Everyday built-in dishwashers from one of the largest appliance makers in the US.
SourceWhirlpool product help: F9E1 error code
Listed on Whirlpool's product-help site for its current built-in dishwashers; models without a display blink it on the Clean light.
Before you book,
in this order.
Each step comes from Whirlpool's own guidance for F9E1 on its dishwashers. Follow it to the end: the last card says whether this is a visit.
Lift out the cylindrical filter at the bottom of the tub and rinse it under the tap.
Follow the drain hose from the back of the machine to the sink and straighten any kink or crushed section.
On a new install tied into a disposer, confirm the knockout plug inside the disposer inlet was removed.
Book a visit if the water still sits after those checks and a 30-second power cut.
What not to do
Standing water with F9E1 is rarely the pump on the first day: a blocked filter or a disposer plug produces the same code.
What you may
notice with it.
The dishwasher problems F9E1 tends to arrive with. Answer these at the dishwasher before anyone is booked.
All problems
Dishwasher Not Draining
6 causes, cheapest first
Where F9E1 usually leads
Drain and pump repair.
Read these
before the visit.
Short guides that make the call quicker and the diagnosis cheaper.
All guidesWhirlpool
dishwashers.
Everyday built-in dishwashers from one of the largest appliance makers in the US.
Whirlpool dishwasher repair
In Whirlpool's own words
Potential Cause: Long Drain
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Listed on Whirlpool's product-help site for its current built-in dishwashers; models without a display blink it on the Clean light.
Whirlpool F9E1 dishwasher repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F9E1.
Can I clear F9E1 myself?
Is F9E1 on my newly installed Whirlpool a sign of a bad pump?
Which filter should I clean for F9E1 on a Whirlpool?
Back to your everyday
Still showing F9E1?
Book with the characters exactly as shown, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.