Fisher & Paykel dishwasher
showing A10
A Fisher & Paykel built-in dishwasher got no water, or not enough: the tap may be off, the pressure too low, or the inlet hose bent.
Mon–Sat, 8am–8pm
- Water supply
- Fill and water valve repair
- Source: Fisher & Paykel
Book a visit
Three short steps, about a minute.
or call (844) 430-4286
Loading appointment form…
The appointment form couldn’t load. Please try again.
What A10
actually means.
A Fisher & Paykel built-in dishwasher got no water, or not enough: the tap may be off, the pressure too low, or the inlet hose bent.
Fisher & Paykel dishwasher display
What to do when A10 shows on the dishwasherKind of codeWater supply
Not enough water arrived, or it arrived too slowly. The supply valve under the sink and the inlet screen are checked before the fill valve itself.
Usually leads toFill and water valve repair
A dishwasher that will not fill, fills too little, or keeps filling, traced through the valve, the float and the supply.
Shows up asDishwasher Not Filling With Water
The cycle starts and hums, but little or no water comes into the tub.
MakeFisher & Paykel
The maker of the DishDrawer, alongside conventional built-in dishwashers.
SourceFisher & Paykel user guide, Series 9 tall dishwasher DW24UT4I2/DW24UNT4X2: 'A' codes
Full-size built-in and integrated dishwashers (Series 5 DW24U2I1 and Series 9 tall DW24UT4I2/DW24UNT4X2), not DishDrawer models.
Before you book,
in this order.
Each step comes from Fisher & Paykel's own guidance for A10 on its dishwashers. Follow it to the end: the last card says whether this is a visit.
Make sure the water is connected and the valve is turned on.
Straighten the inlet hose if it is crimped, and check household pressure.
Confirm the drain hose is connected as the installation instructions show, then restart; book a visit if A10 continues.
Still there?
It usually turns into fill and water valve repair. Book with the code and the model number.
What not to do
Do not overlook the drain hose for a no-water alert. Fisher & Paykel lists an incorrectly connected drain hose among the causes.
What you may
notice with it.
The dishwasher problems A10 tends to arrive with. Answer these at the dishwasher before anyone is booked.
All problems
Where A10 usually leads
Fill and water valve repair.
Read these
before the visit.
Short guides that make the call quicker and the diagnosis cheaper.
All guidesFisher & Paykel
dishwashers.
The maker of the DishDrawer, alongside conventional built-in dishwashers.
Fisher & Paykel dishwasher repair
In Fisher & Paykel's own words
A10 Water tap not turned on.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Full-size built-in and integrated dishwashers (Series 5 DW24U2I1 and Series 9 tall DW24UT4I2/DW24UNT4X2), not DishDrawer models.
Fisher & Paykel A10 dishwasher repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about A10.
Can I clear A10 myself?
What should I check first for Fisher & Paykel A10?
Why would a drain hose cause a no-water alert on my Fisher & Paykel?
Back to your everyday
Still showing A10?
Book with the characters exactly as shown, the full model number, and whether any water is on the floor — for a code, that is where the diagnosis begins.